| Programming Cables: | Serial Cables: | Micro Match Cables: | Other Cables: |
| PGM2KIT PGM06 | CAB9FF6FT CAB9FM6FT CAB3S6FT CAB8M6FT | CAB6MM150 CAB6MM300 | CAB8RIB150 CAB16RIB150 |
PGM2KIT | Programming adaptor for the Microchip PICkit 2 Programmer. | CAD$7.99 In Stock |
|
Description
This adaptor consists of 2 boards connected via a ribbon cable. The connector on the smaller board fits into the programming connector of any Modtronix PIC based SBC board. The 6 pin header on the larger board plugs into the ICSP connector on the Microchip PICkit 2 Programmer.To use this adaptor, you must have a Microchip PICkit 2 Programmer.
Programming Modtronix PIC based boards
This adaptor, along with a PICkit 2 Programmer is ALL you need to debug/program any Modtronix PIC board in circuit - you don't have to remove your PIC from the board to program it! PGM2KIT Cable Signals |  PGM2KIT Programming Adaptor used to program SBC65EC board |
Application Notes
| Web | Data | ||
| Schematics and PCB Layout. |
| ||
| Programming Modtronix PIC based boards |
|
PGM06 | Programming adaptor for the MPLAB ICD 2 Debugger/Programmer. | CAD$7.99 In Stock |
|
Description
This adaptor consists of 2 boards connected via a ribbon cable. The connector on the smaller board fits into the programming connector of any Modtronix PIC based SBC board. The RJ11 connector on the larger board plugs into the cable supplied with Microchip's MPLAB ICD 2 Debugger/Programmer.To use this adaptor, you must have a Microchip MPLAB ICD 2 Debugger/Programmer. Clone devices that use the same pinouts as the original Microchip device should also work, but have not been tested.
Programming Modtronix PIC based boards
This adaptor, along with a MPLAB ICD 2 Debugger/Programmer is ALL you need to debug/program any Modtronix PIC board in circuit - you don't have to remove your PIC from the board to program or debug it!| PGM06 Pins |  PGM06 Programming Adaptor |
Application Notes
| Web | Data | ||
| Schematics and PCB Layout. |
| ||
| Programming Modtronix PIC based boards |
|
CAB9FF6FT | 6 Foot Sub-D female 9 pin to Sub-D female 9 pin null modem serial cable. | CAD$5.70 In Stock |
|
Description
6 Foot Sub-D female 9 pin to Sub-D female 9 pin null modem serial cable. This cable has a Sub-D (D-Sub) 9 pin female connector on each end. Both sides of this cable connects to a male Sub-D communication port (DTE) of a target device, like a personal computer or Modtronix RS232 board. It can for example be used to enable a Modtronix SBC with RS232 interface to communicate with a personal computer. The transmit and receive wires are crossed, to enable two DTE devices to communicate with each other. The wiring is as follows:Pin 2 or connector 1 <--> Pin 3 of connector 2
Pin 3 or connector 1 <--> Pin 2 of connector 2
Pin 5 or connector 1 <--> Pin 5 of connector 2
Some examples of where it can be used are:
Connecting the SBC44B to the serial port of a PC. This will enable these two devices to communicate with each other. It can also be used to program the SBC44B if it is loaded with a bootloader.
Connecting the SBC18DC to the serial port of a PC. This will enable these two devices to communicate with each other. It can also be used to program the SBC18DC if it is loaded with a bootloader.
CAB9FM6FT | 6 Foot Sub-D female 9 pin to Sub-D male 9 pin serial cable. | CAD$5.70 In Stock |
|
Description
6 Foot Sub-D female 9 pin to Sub-D male 9 pin serial cable. This cable has a Sub-D (D-Sub) 9 pin female connector on one end and a Sub-D 9 pin male connector on the other end. One end of this cable connects to a male Sub-D communication port (DTE), and the other end to a female Sub-D communication port (DCE). It can for example be used to enable a Modtronix SBC with RS232 interface to communicate with a DCE device. The wiring is as follows:Pin 2 or connector 1 <--> Pin 2 of connector 2
Pin 3 or connector 1 <--> Pin 3 of connector 2
Pin 5 or connector 1 <--> Pin 5 of connector 2
CAB3S6FT | 6 Foot Sub-D female 9 pin serial port cable. The one side of this cable connects to a 3 pin serial connector on certian MicroX Main boards (SBC boards). | CAD$5.70 In Stock |
|
Description
6 Foot Sub-D female 9 pin serial port cable. The one side of this cable connects to a 3 pin serial connector on certian MicroX Main boards (SBC boards). The other side will connect to the male Sub-D communication port (DTE) of a target device, like a personal computer. It can for example be used to enable a MicroX Main Board to communicate with a personal computer. When connected to a MicroX Main Board, the following signals will be present on the Sub-D female connector.Pin 2 - Transmit data (RS232 levels)
Pin 3 - Receive data (RS232 levels)
Pin 5 - Ground
CAB8M6FT | Serial Cable with RJ-45 plug, and D-Sub 9 pin female connector, 1.8m long. | CAD$5.70 In Stock |
|
Description
This is a 1,8m (6 Foot) Serial Cable with RJ-45 plug on one end, and D-Sub 9 pin female connector on other end.This cable enables a Modtronix device with a RJ-45 RS232 communications port to be connected to the RS232 communications port (D-Sub 9 pin male connector) of a DTE device, like a PC for example. The one end of this cable plugs into the RJ-45 port of the Modtronix device, and the other end to the DTE device's Male DB-9 connector.
All Modtronix devices with RS232 DB-9 Male connectors are DTE devices. A PC is also a DTE device. This cable can be used to connect a Modtronix device with RJ-45 RS232 Communication port to a PC.
The CAB8M6FT datasheet can be downloaded here.
This cable is similar to the Moxa CBL-RJ45F9-150 cable. The Moxa cable has two extra wires, one for DSR (RJ-45 pin 1 and D-Sub pin 4), and one for DTR (RJ-45 pin 8 and D-Sub pin 6). Most modern equipment do not use the DSR and DTR signals any more, and they are not required. Modtronix devices with RJ-45 RS232 ports can use either of these two cables, and do not use the DSR and DTR signals.
Additional Photos
 Shows the CAB8M6FT plugged into a RJ-45 port on a Single Board Computer. Larger photo |
 Wiring Diagram |
CAB6MM150 | Ribbon cable with two 6 pin Micro Match connectors, 150mm long . | CAD$3.99 In Stock |
|
Description
This is a 150mm (5.9") ribbon cable with two 6 Pin Micro Match connectors on either end.It can be used to connect I2C or SPI devices together. For example, the Modtronix LCD2S range of serial LCD displays and one of our Single Board Computers with a Micro Match connector.
Additional Photos
 SBC28PC Single board computer with LCD2S serial LCD display. Larger photo |  SBC65EC Single board computer with LCD2S serial LCD display. Larger photo |
CAB6MM300 | Ribbon cable with two 6 pin Micro Match connectors, 300mm long . | CAD$4.95 In Stock |
|
Description
This is a 300mm (11.8") ribbon cable with two 6 Pin Micro Match connectors on either end.It can be used to connect I2C or SPI devices together. For example, the Modtronix LCD2S range of serial LCD displays and one of our Single Board Computers with a Micro Match connector.
Additional Photos
| SBC28PC Single board computer with LCD2S serial LCD display. Larger photo | SBC65EC Single board computer with LCD2S serial LCD display. Larger photo |
CAB8RIB150 | Ribbon cable with two 8 pin, 2.54mm (0.1 Inches) female pin headers, 180mm long, can be used for Keypads. | CAD$3.99 In Stock |
|
Description
This is a 180mm (7") ribbon cable with two 8 pin, 2.54mm (0.1") female connectors on either end.It can be used to plug onto a 2.54mm (0.1") pin header, like the HDR1X32M254 for example.
It can also be used to connect a 12 button or 16 button keypad to our LCD2S range of serial LCD displays with keypad decoder.
Additional Photos
 Connecting LCD2S Serial LCD Display with Keypad. Larger photo |  Connecting LCD2S Serial LCD Display with Keypad. Larger photo |
CAB16RIB150 | Ribbon cable with two 16 pin, 2.54mm (0.1") female pin headers, 180mm long, can be used for LCD displays. | CAD$4.60 In Stock |
|
Description
This is a 180mm (7") ribbon cable with two 16 pin, 2.54mm (0.1") female connectors on either end.It can be used to plug onto a 2.54mm (0.1") pin header, like the HDR1X32M254 for example.
When soldering a pin header to the back of an LCD Character Display, it can be used to connect the LCD to a controller board.
Additional Photos
 LCD Display with pin header soldered onto back. Larger photo |  LCD Display with pin header soldered onto back, and cable plugged into it. Larger photo |
